Packing list
The type and quantity of accessories may change from time to time. Please refer to the actual items you receive.
| H2D Laser Full Combo | H2D AMS Combo | H2D |
|---|---|---|
| H2D AMS 2 Pro Build Plate (Pre-installed on heatbed) | H2D AMS 2 Pro Build Plate (Pre-installed on heatbed) | H2D Build Plate (Pre-installed on heatbed) |
image | image | image |
| Safety Key*2（one attached to the rear board, one in the Emergency Stop Button.） | Safety Key (attached to the rear board) | Safety Key (attached to the rear board) |
| Accessory Box 1. Cutting Module - Cutting Module - Pen Holder - Pen Height Calibrator - Pen Fixture 2.Emergency Stop Button 3. Power Cord 4. Bambu Bus Cable 6-pin 5. Marker Pen 6. Spool Holder (inside the rectangular accessory box) image | Spool Holder Power Cord (in AMS) image | Spool Holder * 2 Power Cord |
| Tool Box - 0.4mm Nozzle - Silicone Sock for Hotend - Filament Cutter - 45° Fine-point Blade - Unclogging Pin - Nozzle Wiping Pad - Nozzle Blocker - Scraper Blade - Weeding Tool - Screws for Scraper - Screws for Spool Holder - Allen Key (H1.5 & H2.0) - Laser Homing Area XY & Z Marker - Rubber Screws for Chamber Exhaust Fan - Camera Privacy Cover - Lubricant Oil - Lubricant Grease | Tool Box - 0.4mm Nozzle - Silicone Sock for Hotend - Filament Cutter - Unclogging Pin - Nozzle Wiping Pad - Nozzle Blocker - Scraper Blade - Screws for Scraper - Screws for Spool Holder - Allen Key (H1.5 & H2.0) - Camera Privacy Cover - Lubricant Oil - Lubricant Grease (Some versions include a white grease) | Tool Box - 0.4mm Nozzle - Silicone Sock for Hotend - Filament Cutter - Unclogging Pin - Nozzle Wiping Pad - Nozzle Blocker - Scraper Blade - Screws for Scraper - Screws for Spool Holder - Allen Key (H1.5 & H2.0) - Camera Privacy Cover - Lubricant Oil - Lubricant Grease |
| PTFE Tube Desiccant | PTFE Tube Desiccant | PTFE Tube Desiccant |
| Quick Start Guide Warranty Leaflet Disclaimer and safety guidelines | Quick Start Guide Warranty Leaflet Disclaimer and safety guidelines | Quick Start Guide Warranty Leaflet Disclaimer and safety guidelines |
| Supply Box - Laser Platform - Cutting Platform - StrongGrip Cutting Mat (Pre-installed on Cutting Platform) - LightGrip Cutting Mat (Pre-installed on Cutting Platform) - Laser Slats Pack - Material Pins - Basswood Plywood - Cork Sheet - Heat Transfer Vinyl - Pearlescent White Greeting Card Set - Rectangular PU Iron-on Patch - Round Stainless Steel Tag (Large & Small) - Brush | / | / |
| The followings are packaged inside AMS 2 Pro: Smoke Ventilation Pipe Ventilation Pipe Adapter Pipe Clamp Screws for Ventilation Pipe Adapter Air Pump Intake | / | / |
Accessory List
| Picture | Descriptions |
|---|---|
image | Cutting Module Cutting Module Installation Guide Introduction to the main components and usage process of the cutting&drawing module |
image | Pen Holder & Pen Height Calibrator Introduction to the main components and usage process of the cutting&drawing module |
image | Pen Fixture Introduction to the main components and usage process of the cutting&drawing module |
image | 0.4mm Nozzle *1 & Silicone Sock for Hotend *1 Replace Hotend |
image | Filament Cutter Replace H2D Filament Cutter Lever and Blade |
image | 45° Fine-point Blade |
image | Unclogging Pin, can be used to unclog hotend H2D Hotend Unclogging Procedure |
image | Nozzle Wiping Pad |
image | Nozzle Blocker Repair and Replace H2D Flow Blocker |
image | Scraper Blade Cutting Module Assist Tool (weeding tool, scraper and roller) Usage Introduction |
image | Weeding Tool Cutting Module Assist Tool (weeding tool, scraper and roller) Usage Introduction |
image | Screws for Spool Holder |
image | Screws for Scraper |
image | Allen Key (H1.5 & H2.0) |
image | Laser Homing Area XY & Z Marker |
image | Rubber Screws for Chamber Exhaust Fan Replace H2D Chamber Exhaust Fan |
image | Camera Privacy Cover |
image | Lubricant Oil, typically used for the lubrication of linear guides, slide rails, and steel shafts |
image | Lubricant Grease, used for lubricating lead screws or eliminating noise issues between belts and idler pulleys |
image | Emergency Stop Button & Safety Key Install the emergency stop button |
image | Power Cord |
image | Bambu Bus Cable 6-pin |
image | Marker Pen |
image | Spool Holder |
image | Laser Platform Introduction to the Laser Platform Install the laser platform Introduction to the main components and workflow of the laser module |
image | Cutting Platform Introduction to the Cutting Platform Cutting Protection Base StrongGrip Cutting Mat LightGrip Cutting Mat |
image | Laser Slats Pack Install the laser platform |
image | Material Pins Material pins can be used to crimp the materials, which can make the materials flat and not easy to move. The method of use is to magnetically absorb it into the vertical edges on both sides of the laser platform, and crimp it to the edge of the materials with the inclined surface facing down |
image | Basswood Plywood |
image | Cork Sheet |
image | Heat Transfer Vinyl |
image | Protective Paper for Heat Transfer |
image | Pearlescent White Greeting Card Set |
image | Rectangular PU Iron-on Patch |
image | Round Stainless Steel Tag (Large & Small) |
image | Brush |
image | Smoke Ventilation Pipe Install Smoke Ventilation Pipe |
image | Ventilation Pipe Adapter Install Smoke Ventilation Pipe |
image | Pipe Clamp Install Smoke Ventilation Pipe |
image | Screws for Ventilation Pipe Adapter Install Smoke Ventilation Pipe |
image | Air Pump Intake Install Air Pump Intake |
image | PTFE Tube |
image | Desiccant, placed inside the AMS to keep the air inside dry, thus protecting the filaments from moisture |
End Notes
Чтобы обеспечить безопасное и эффективное выполнение, если у вас есть вопросы или сомнения по поводу процесса, описанного в этой статье, мы рекомендуем отправить тикет в техподдержку, касающийся вашей проблемы.
Пожалуйста, приложите фотографию или видео, иллюстрирующее проблему, а также любую дополнительную информацию, связанную с вашим inquiry.