Video Guide
Operation Steps
Take out the AMS 2 Pro
- Open the carton and take out the AMS 2 Pro.
image | image |
image | image |
- Remove the two black foams on the left and right.
image | image |
- Remove the tape and take out the AMS 2 Pro.
image | image | image |
Take out the accessories
- Remove the instruction manual.
image | image |
- Remove the protective film.
image | image |
image | image |
- Open the top cover and take out the black foam and cable bag.
image | image | image |
- Remove the sticker and take out the desiccant.
image | image |
Place the desiccant
Remove the packaging and place the desiccant in the AMS 2 Pro.
image | image |
image | image |
Check the active drive shafts
Vibrations during transportation may cause the drive shafts on the slots to dislodge. Please check and ensure each shaft is properly assembled to prevent filament disarray due to failure to turn the spool to rewind it.
Connect the tube
Remove the tape and remove the tube.
image | image |
Connect the printer and AMS 2 Pro
- Connect the AMS 2 Pro to H2 series printers
- Connect the AMS 2 Pro to X2D Printer
- Connect the AMS 2 Pro to X1 and P1 series printers
- Connecting the AMS 2 Pro to the P2S Printer
- Connect the AMS 2 Pro to A1 series printers
Place the top glass cover and AMS 2 Pro on top of the printer.
Insert the PTFE tube into the AMS 2 Pro's filament outlet and any PTFE tube coupler of the printer, and push the tube forward for approximately 10 cm until it stops (if you can see the PTFE tube from the window next to the buffer from the front of the printer, it is correctly inserted)
The upper and lower PTFE tube couplers correspond to different hotends. Connecting the AMS 2 Pro to the upper coupler allows the right hotend to print in multiple colors. Connecting it to the lower coupler allows multi-color printing with the left hotend. Using two AMS 2 Pro units allows both hotends to support multi-color printing independently
| Connect PTFE tubes | Make sure you can see the tube in this window |
|---|---|
image | image |
Connect the Bambu Bus Cable 6-pin to the printer and either 6-pin port of the AMS 2 Pro.
At this point, the connection of a single AMS 2 Pro is complete. If you only use one AMS 2 Pro, this connection method can normally use all AMS functions (including drying) without the need for an additional power adapter.
- Insert one end of the PTFE tube into the AMS 2 Pro outlet. It is recommended to insert the other end into the upper inlet of the filament buffer (corresponding to the left hotend).
- Connect the Bambu Bus Cable 6-pin to the printer and either 6-pin port of the AMS 2 Pro.
Please use the 6-pin cable for AMS 2 Pro. The cable for the previous generation of AMS is not compatible with AMS 2 Pro.
Place the top glass cover on the top of the printer.
Use 2 M3*21.5 screws to fix the filament buffer to the printer. Insert one end of the 550 mm PTFE tube to the filament outlet of the AMS 2 Pro, and the other end to the left of the filament buffer. Insert one end of the 370 mm PTFE tube to the PTFE tube coupler of the printer, and the other end to the right of the filament buffer.
imageConnect the L-shape end of the Bambu Bus cable 4-pin to the printer, and the other end to the bottom the filament buffer. Connect one end of the Bambu Bus cable 6-pin to either 6-pin port of the AMS 2 Pro, and the other end to the left of the filament buffer. Connect the 24V 4A power supply to the power connector of the AMS 2 Pro if you need to use the drying function.
imagePlease use the 6-pin cable for AMS 2 Pro and AMS HT. The cable for the previous generation of AMS is not compatible with AMS 2 Pro.
- Place the AMS 2 Pro on top of the printer.
- Insert one end of the 350 mm PTFE tube into the printer’s filament inlet, and connect the other end to the right side of the buffer.
- Insert one end of the 600 mm PTFE tube into the AMS 2 Pro’s filament outlet and push it in until fully seated. Connect the other end to any filament inlet on the left side of the buffer.
image - Plug both ends of the 6-pin cable into any 6-pin port on the AMS 2 Pro and the printer’s buffer, respectively.
image
A1: Please refer to: A1 Series AMS Connection Guide.
A2L: Please refer to: A2L AMS Connection Guide